eLightbars Home

the Internet's largest lightbar, siren, and emergency equipment forum

Make a contribution

Forum options:    SearchSearch   Member listMember list  RegisterRegister  ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in

Notice: Thanks for your patience as we work to restore full service. In the mean time, please try out our new chat room.

omega 90 harness p/n's?


 
Post new topic   Reply to topic    eLightbars.org Forum -> Non-lighting warning equipment
Author Message
High_Order1
New member
New member


Joined: 31 Oct 2006
Posts: 14
Location: near Oak Ridge, Tennessee
PostPosted: Thu 20-Nov-2008 12:43    Post subject: omega 90 harness p/n's? Reply with quote
Tried posting this a couple of times but got some kind of funky error. Anyway, I've done some searching, but can't find the answer.

Any of you know where to source the three plugs to fit the jacks on the unitrol siren box? The cheapest I can find a made up harness is waay more than I want to spend.


Thanks!

-Shawn
srh@esper.com
Back to top    URL
Rofocowboy84
Turbo Poster


Joined: 12 Jul 2007
Posts: 2775
Location: Montgomery County, PENNSYLVANIA!!!
PostPosted: Thu 20-Nov-2008 22:57    Post subject: Reply with quote
+1 for this, I definitely need one too.

Also, if the OP doesn't mind me adding on to his question....

Is it possible to control the Omega 90 amps with just switches, or do you need the motorcycle card? I was thinking about replacing the \"lighting\" switches on my Carson Volunteer and using them to control the Unitrol. I'm hoping I don't need the card, because it's expensive and it seems to limit your options. Thanks!
Back to top    URL
Solvarex
Member
Member


Joined: 25 Mar 2007
Posts: 42
Location: Winnipeg MB Canada
PostPosted: Fri 21-Nov-2008 00:40    Post subject: Reply with quote
The Omega amp just needs +12VDC to activate the tones, no board required.
Back to top    URL
Rofocowboy84
Turbo Poster


Joined: 12 Jul 2007
Posts: 2775
Location: Montgomery County, PENNSYLVANIA!!!
PostPosted: Fri 21-Nov-2008 00:44    Post subject: Re: Reply with quote
[quote:8d5d18b150=\"Solvarex\"]The Omega amp just needs +12VDC to activate the tones, no board required.


Sweet, now I just need to get the cable, or just a connector and I can make my own cable.....
Back to top    URL
OTFD122
Frequent Poster


Joined: 04 Dec 2005
Posts: 1855
Location: Rochester, MI
PostPosted: Fri 21-Nov-2008 06:21    Post subject: Re: Reply with quote
[quote:4b204b0754=\"Rofocowboy84\"][quote:4b204b0754=\"Solvarex\"]The Omega amp just needs +12VDC to activate the tones, no board required.


Sweet, now I just need to get the cable, or just a connector and I can make my own cable.....

No motorcycle card here... Wink

http://www.youtube.com/watch?v=T_bGb2vtJV8 Back to top    URL
High_Order1
New member
New member


Joined: 31 Oct 2006
Posts: 14
Location: near Oak Ridge, Tennessee
PostPosted: Sun 23-Nov-2008 20:54    Post subject: Reply with quote
wish I could respond....
Back to top    URL
Display posts from previous:   
Post new topic   Reply to topic    eLightbars.org Forum -> Non-lighting warning equipment All times are GMT - 6 Hours
Page 1 of 1

 

By accessing any part of this site, you acknowledge/accept the terms and conditions laid out in our site guidelines.

© Blake Barr, all rights reserved.