Search results

Looking to install a hlf on a retail 19 Tahoe. I see I can connect the headlight wires under the under hood fuse panel. Is there a recommendation on using a whelen or sound off isolated flasher. The older Tahoe had a relay in the panel that isolated the output from BCM.

Looking for a dual switch whelen avenger 2 power cord. Need the one that turns on mode 1 and mode 2. Thanks

It has to be a relay. I used a Lin3 which it was able to flash but when i switched to a double avenger it went bonkers. Its a very low current to activate an external relay.

Well i got some info. Apparently the outputs for the lights on this are negative switch low current. Basically have to use a relay on each output to turn on a circuit. Hence why there is no heavy positive input on these.

Looking for info on a federal made smart siren for ford crown Vic’s. Has a special ford plug on it and has a ford part number. 5W7J-70443-aa. Tried calling federal and the guy I spoke with said he had nothing and passed me off to crown America which I can’t also find info. Does anyone have...

Trying to install one for a fire dept. which side is better to access the headlight wiring. I'm thinking passenger side.

Looking for a complete whelen double avenger suction cup bracket. Need the pieces also that attach to the light.

Looking to see what people have done with whelen heads out of warranty where the chrome material flakes off. Got a freedom corner practically all black plastic. Wonder if anyone use a reflective tape to try and restore them somewhat.

Are these the syncable models?

Looking for an installation kit for a 2100 siren. Have the box and hhch but no harnesses. Thanks

Yes but this isn't a towman bar. has 4 corners and 2 pairs of leds front and back. Only has one harness coming out of bar. I emailed whelen and they sent me the same towman manual. Must not be a manual for the regular economy liberty.

Did whelen ever make a liberty 48" lightbar with just two small flasher modules in it, instead of a full i/o board with a red/black power wire. Picked up two units at an auction sale and the labels were removed from the base so Im not sure on the models. These are passive led's with 06/07...

PM Sent

Can you onvert code 3 optix heads in 21oo bars

Looking for a dominator end cap with hole for wiring. thanks

Is there a second bracket?  I only see one in picture

The part that I seen in one new article was he was a firefigther not a dispatcher.  He was detailed to there for what I dont know.  911 operators receive specific training on how to keep people calm on phones etc..   Still was wrong to hang up. But as usual all the media only gives part of the info.

Any alleys in this.  I dont see takedowns.

Looking for a used havis console specific for the trailblazer.  reply via PM. thanks

Do you have paperwork that was purchased from a dealer.  The label shows it to be Developmental firmware.  Should be R not D

Need a dominator end cap prefer with wiring hole.  Will take one without as I could just drill a hole if needed.  Had one break off when trying to remove a seized screw from housing. reply via PM Frank

Saw this go dirt cheap on govdeals.  Damm if i didnt live 4 hours away.

Thats the same manual I found. Problem is i dont have any of the multicolor wires. Just a row of solder pads on top board. Seen a jumper soldered between two points also the cig cord is soldered to them also.

unlisted would you have any info on these lights. Ones I bought had cig cords on them and cant find anything on how to change patterns. I found one that references multiconductor wire but mine dont have that.

Have you done anything on 911ep 360 stars. Got one here which is half red/blue and would like to see if it can be converted to all blue? Will try to take a photo tomorrow. Frank

Are the frames different between the 44 and 48/50 models? I picked up a 44" model but I see a seller selling the center sections for the justice on ebay?

Could you pm with your shipping. Can talon heads be converted? What about dominator tir3 heads 2 wire? Thanks

Are the decals removed and how many holes in vehicle. Any rust on vehicle.

Plus just for reference that the PSP lightbars were Vision bars not vectors.

Does anyone know how to change the opticom coded transmitter id's? The tomar pack has a db-9 connector on it? Is there software that is needed to repogram the id? Thanks